Blog

7 Domestic Hot Water Sizing Mistakes to Catch Before Construction

Seven practical checks for DHW sizing, from diversity and hot-water demand to HIU performance, primary flows and combined heating loads.

Domestic hot water (DHW) sizing requires more than a peak demand figure. Engineers need to apply appropriate diversity, calculate heating-side flows through heat interface units (HIUs) or heat exchangers, and combine hot-water and space-heating loads correctly. Hysopt’s domestic hot water design and simulation software connects these calculations, helping teams understand how demand assumptions affect primary pipework and plant selection.

A tidy equipment schedule can conceal a weak design assumption. By the time it reaches procurement, that assumption may already be embedded in pipe diameters, pump duties and plant capacity.

These seven checks help bring it back into view.

‍

1. Adding every outlet’s peak demand

‍

Adding the maximum hot-water flow of every shower, basin and kitchen tap produces a theoretical total. It does not establish the simultaneous demand the system should be designed to serve.

Diversity accounts for the fact that outlets are not necessarily used together. However, the appropriate calculation depends on the application and the selected method. A pattern suitable for apartments should not simply be transferred to accommodation with strongly coordinated shower use.

Start with the demand brief: building use, dwelling or outlet numbers, expected usage and required service conditions. Then select the appropriate calculation basis.

Check before issue: Does the schedule show theoretical total demand or diversified design demand? Make that distinction explicit.

‍

2. Applying diversity twice without checking the method

‍

Diversity needs to be carried through the calculation correctly as dwellings join branches and branches join the main distribution.

A flow that has already been diversified for one dwelling is not necessarily the correct starting point for another simple percentage reduction. Equally, adding individual diversified peaks does not automatically produce the correct building-level peak.

Hysopt’s diversity and aggregation workflow distinguishes calculations within a dwelling from those across multiple dwellings. That distinction matters when a scheme grows or its apartment mix changes.

Check before issue: Trace one branch back to its original inputs. Identify where diversity enters, which method is used, and how it propagates upstream. Avoid unexplained “additional diversity” allowances.

‍

3. Changing temperatures but keeping the original hot-water flows

‍

Hot-water flow at the source and mixed-water flow at the outlet are different quantities.

If an outlet must deliver the same mixed flow at the same temperature, changing the hot or cold supply temperature changes the required hot-water contribution. Reusing the original hot-water flow can therefore make the revised design inconsistent with the service requirement.

Hysopt documents tap-flow recalculation for changed temperature regimes. This is particularly relevant when a concept changes during design development.

Check before issue: When temperatures change, revisit the demand inputs and heat-transfer calculation together. Retain the required outlet service and the project’s temperature and hygiene requirements as design constraints.

‍

4. Using the potable DHW flow to size the primary heating circuit

‍

A heat interface unit (HIU) transfers heat between the primary heating circuit and potable DHW through a heat exchanger. It does not require the water flows on those circuits to be equal.

Neglecting losses, the transferred thermal power is the same on both sides. The flow depends on each side’s temperature difference.

For a simple water-based calculation:

Flow in m³/h ≈ 0.86 × thermal power in kW ÷ temperature difference in K

Consider an illustrative 40 kW duty:

The same heat duty produces twice the flow on the primary side. These values illustrate the calculation, not recommended operating temperatures.

A real HIU also requires the heat exchanger to achieve the assumed duty and temperatures. Its characteristics affect the primary return temperature and therefore the primary flow.

Check before issue: Label every flow by circuit. Do not copy potable demand directly into primary pump or pipe calculations.

‍

5. Combining heating and DHW with the wrong priority assumption

‍

A dwelling’s HIU may suspend space heating while producing hot water. That does not mean an entire building is either heating or drawing hot water.

Some apartments may be in DHW mode while others continue heating. Common pipework must reflect that combination.

Hysopt provides different aggregation methods for diversified space-heating and DHW loads, including maximum, weighted-average and sum approaches. These represent different assumptions. They are not interchangeable shortcuts for obtaining a smaller pipe.

The calculation must also track power and volume flow separately. The load with the highest thermal duty does not necessarily create the highest flow.

Check before issue: Confirm the actual priority behaviour and the project’s required aggregation method. Modelling DHW and heating together makes the consequences visible across the shared primary system.

‍

6. Selecting an HIU by headline output alone

‍

An HIU’s published duty belongs to a set of operating conditions.

Changing primary supply temperature, cold-water temperature or the required DHW output can change the flow needed to transfer that duty. A fixed return-temperature assumption can also conceal an unrealistic heat-exchanger selection.

Hysopt’s HIU models can use manufacturer performance information to calculate heat transfer, primary flow and return temperature. This makes it possible to examine the unit as part of its connected system.

Check before issue: Review the proposed unit at the project’s actual design conditions. Record the performance data used, then check what the resulting primary flow means for pipework, pumping and return temperatures.

‍

7. Stopping at the design condition

‍

Design flows establish a basis for selecting equipment. The next question is how that equipment responds as demand changes.

Check what happens when an HIU switches to DHW production, when several dwellings draw hot water together, and when demand falls again. Look at primary flow, return temperature and control response.

Hysopt supports detailed dynamic HIU models for investigating these interactions. The model needs to represent the controls and components relevant to the decision being assessed.

Check before issue: Use the design calculation for equipment selection, then test the operating scenarios that could challenge the proposed system.

‍

Frequently asked questions

What information is needed for domestic hot water sizing?

Start with the building use, relevant outlet or dwelling data, required hot-water service, temperature assumptions and applicable demand method. For the primary heating system, also define the heat exchanger or HIU performance, space-heating loads and control priorities. Document where assumptions replace project data.

What is the difference between DHW diversity and aggregation?

Diversity estimates coincident demand within a defined group of users or outlets. Aggregation combines calculated demands across branches or applications. In a shared heating system, engineers must also combine space heating and DHW while accounting for their different temperature regimes and operating modes.

Are DHW flow and primary heating flow the same?

Usually they should be calculated separately. A heat exchanger transfers the required thermal power between circuits, but each circuit’s flow depends on its temperature difference. The exchanger’s performance affects the primary return temperature and the flow needed to deliver the duty.

Should space heating and DHW loads always be added together?

The aggregation method must reflect the design requirements and system configuration. Local DHW priority does not eliminate simultaneous heating elsewhere in the building. Calculate the relevant diversified loads and apply the chosen method consistently to both thermal power and volume flow.

Can Hysopt support DHW pipe sizing?

Hysopt calculates diversified DHW loads and their effect on primary heating flows. Engineers can use those flows to size the primary heating pipework serving HIUs and DHW production, while keeping heat-exchanger performance and temperature assumptions connected to the calculation.

Check the assumptions behind your DHW design

‍

Changing an HIU, temperature regime or demand assumption can affect more than one line in the equipment schedule. Connect those decisions before the design reaches procurement.

Explore how Hysopt connects demand, HIUs and primary heating calculations, then use the DHW enquiry form to tell us what you need to assess.

Discuss your DHW design with Hysopt

READ ALSO

7 shifts reshaping HVAC engineering in 2027

Discover the key trends transforming HVAC design across buildings, data centres and district energy networks.

From AI-driven engineering and grid constraints to system flexibility and verified performance, explore what’s changing, why it matters and how to prepare.

Ready to validate HVAC performance before construction?

Use Hysopt to simulate hydronic systems, compare design scenarios and reduce oversizing risk.

Explore more

Close-up of an outdoor air-source heat pump covered in frost and condensation on a cold morning, highlighting winter operating conditions for domestic hot water production.
Blog

A Practical Guide to Heat Pumps for Domestic Hot Water

A heat pump’s rated output is only the starting point. Learn how to assess DHW charging temperatures, storage recovery, booster arrangements and shared plant controls.
Close-up of an insulated domestic hot water storage tank with copper piping, brass fittings and a plate heat exchanger, illustrating DHW storage and heat recovery capacity.
Blog

How to Size DHW Storage for Peak Demand and Recovery

A practical method for balancing DHW storage, charging power and recovery, with a worked energy example and the checks needed before selecting a cylinder.
Unfinished commercial building interior with exposed HVAC ductwork, insulated pipes and cable trays, showing the installation stage where accurate IFC model handover supports construction coordination.
Blog

The Complete Guide to HVAC IFC Handover in 2026

Learn how to improve HVAC BIM data interoperability during IFC handover, preserve engineering calculations and prevent information loss between design software and BIM models.